OPER ATOR'S MANUALMOW’N MACHINEVACUUMMAN0116 Rev. 4/15/2004Tested. Proven. Unbeatable.D5221T, D6121Ton F-SeriesPower Units
8 Dealer Check ListMAN0116 (4/15/2004)DEALER CHECK LISTSPRE-DELIVERY CHECK LIST(DEALER’S RESPONSIBILITY)Inspect the equipment thoroughly after assembl
Service 9MAN0116 (Rev. 4/15/2004)SERVICEReplace Vacuum Housing Bearings1. Remove vacuum housing from deck.2. Remove hose adapter (4) from vacuum housi
10 ServiceMAN0116 (Rev. 4/15/2004)Service Cont’dReplace Vacuum Spindle Bearings1. Remove vacuum housing from deck.2. Remove bearing mount (41) from De
Service 11MAN0116 (Rev. 4/15/2004)NOTES
12 PartsMAN0116 (Rev. 4/15/2004)VACUUM & DRIVE ASSEMBLY 911121081211224521196234741235346564544194341421413115110155111521617181940392038374849352
Parts 13MAN0116 (Rev. 4/15/2004)VACUUM & DRIVE ASSEMBLY PARTS LISTRef Part No. Description1 71492 Vacuum fan housing2 71493 Angled blower chute3 7
14 AppendixBolt Torque & Size Charts (Rev. 8/14/2002)BOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque value or t
Appendix 15Bolt Torque & Size Charts (Rev. 8/14/2002)BOLT SIZE CHARTNOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for
F-8495 MM Repair Parts (Revised 7/15/2003) © 2001 Woods Equipment Company. All rights reserved.Woods Equipment Company2606 South Illinois Route 2 Post
F-8045 MM (Rev. 1/28/2004)Woods Equipment Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061815-732-2141 tel815-732-7580 fa
ii IntroductionGen’l (Rev. 3/30/2004)TO THE DEALER:Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read m
Woods Equipment Company2606 Illinois Route 2 SouthPost Office Box 1000Oregon, Illinois 61061815-732-2141 tel815-732-7580 fax© 2001 Woods Equipment Com
Introduction 1MAN0116 (Rev. 4/15/2004)TABLE OF CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 SafetyMow’n Machine Vacuum (9/11/00)TRAINING Safety instructions are important! Read allattachment and power unit manuals; follow allsafety rules a
Safety 3Mow’n Machine Vacuum (9/11/00) Before performing any service or maintenance,lower attachment to ground, turn off power unitengine, remove key
4 SafetyMAN0116 (Rev. 4/15/2004)MODELNO. SERIALNO. MASS (KG)ID NO.OREGON, IL U.S.A.YR OF MFG.2 - SERIAL NUMBER PLATESHIELD MISSINGDANGER188693 - PN 18
Installation 5MAN0116 (Rev. 4/15/2004)VACUUM INSTALLATIONRemove Discharge Chute 1. Remove mower deck discharge chute by removingthe two 1/4 NC hex nut
6 InstallationMAN0116 (Rev. 4/15/2004)Attach Discharge Chute Be sure either the discharge chute, mulchingend cap, or complete vacuum attachment isin
Installation 7MAN0116 (Rev. 4/15/2004) Figure 6. Bearing Mount Assembly InstallationInstall Vacuum Drive Belt 1. Install belt (37) over sheaves and id
Commentaires sur ces manuels